Description
This PIXHAWK 2.4.8 Full Combo Kit (NDK03) consists of all-in-one required products for the drone flight controller. Find all products included in this kit below in the “Package Includes” section.
The PIXHAWK PX4 2.4.8 Flight Controller is a high-performance autopilot-on-module suitable for fixed-wing, multi-rotors, helicopters, cars, boats, and any other robotic platform that can move. It is targeted towards high-end research, amateur, and industry needs, and combines the functionality of the PX4FMU + PX4IO.
A new generation Ublox GPS NEO-M8N, with low power consumption and high precision, provides ultimate accuracy of 0.6 meters (actually almost 0.9 meters), greater than the previous generation NEO-7N (1.4-1.6 meters accuracy). It supports GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1 protocol, and more.
The GPS Folding Antenna Base mount comes with a laser-cut adhesive pad to quickly attach your GPS module, while the mount itself can be fixed to your craft using the base plate M3 hole or the cross slides.
Specifications and Features:
Pixhawk V2.4.8 Flight board:
- The advanced 32-bit ARM CortexM4 high-performance processors can run Nux RTOS real-time operating system.
- 14 PWM / servo output.
- Bus interface (UART, I2C, SPI, CAN).
- Integrated backup power and backup controller. If the primary controller fails, the system will failover to the backup control for safety.
- Supports both automatic and manual modes.
- Provides redundant power input and failover.
- Multicolor LED lights.
- Multi-tone buzzer interface.
- Micro SD card for recording flight data.
Processor:
- 32-bit STM32F427 Cortex M4 core with FPU.
- 168 MHz clock speed.
- 128 KB RAM.
- 2 MB Flash.
- 32-bit STM32F103 failsafe co-processor.
Sensors:
- ST Micro L3GD20H 16-bit gyroscope.
- ST Micro X4HBA 303H 14-bit accelerometer/magnetometer.
- Invensense MPU 6000 3-axis accelerometer/gyroscope.
- MEAS MS5607 barometer.
Interfaces:
- 5x UART (serial ports), one high-power capable, 2x with HW flow control.
- 2x CAN (one with an internal 3.3V transceiver, one on expansion connector).
- Spektrum DSM / DSM2 / DSM-X® Satellite compatible input.
- Futaba S.BUS® compatible input and output.
- PPM sum signal input.
- RSSI (PWM or voltage) input.
- I2C.
- SPI.
- 3.3 and 6.6V ADC inputs.
- Internal micro USB port and external micro USB port extension.
PIXHAWK PPM Encoder Module:
- Supports the input channels: 8.
- Output: PPM SUM × 1 / MUX × 1.
Glass Fiber Flight Controller Anti-vibration/Shock Absorber Set:
- Color: Black.
- Material: Glass-fiber.
- Compatible with various open-source flight controllers, including APM 2.5/2.6/2.8, KK, MWC, and Pixhawk 2.4.
NEO-M8N GPS Module:
- Receiver type: 72-channel Ublox M8 engine.
- Supports GPS/QZSS L1 C/A, GLONASS L10F, BeiDou B1.
- SBAS L1 C/A: WAAS, EGNOS, MSAS.
- Galileo-ready E1B/C (NEO-M8N).
- Nav. update rate: Single GNSS up to 18 Hz, Concurrent GNSS up to 10 Hz.
- Position accuracy: 2.0 m CEP.
- Cold start: 26 s, Aided starts: 2 s, Reacquisition: 1.5 s.
- Sensitivity: Tracking & Nav: –167 dBm, Cold start: –148 dBm, Hot start: –156 dBm.
- Assistance: AssistNow GNSS Online, AssistNow GNSS Offline (up to 35 days), AssistNow Autonomous (up to 6 days).
- Compliance with OMA SUPL & 3GPP standards.
- Noise figure: On-chip LNA for lowest noise figure.
- Supported antennas: Active and passive.
GPS Folding Base Antenna Set:
- Material: CNC Aluminum alloy, carbon glass fiber rod.
- Mounting rod diameter: 4mm.
- Length of rod: 14 cm.
- GPS plate diameter: 40 mm.
- Base plate diameter: 35 mm.
- Mounting hole spacing: 16-35mm.
- Weight: 20g.
- Color: Anodised black.
- Note: Adhesive pad not included.
APM 2.5.2/2.6/2.8 Pixhawk Power Module V1.0:
- Max input voltage: 28V.
- Max current sensing: 90A.
- Voltage and current measurement configured for 5V ADC.
- Switching regulator outputs 5.3V and 3A max.
- 6-pos DF13 cable plugs directly into the APM 2.5’s ‘PM’ connector.
- Supports 6S battery.
Package Includes:
- 1 x Pixhawk V2.4.8 Flight board with Original Shell.
- 1 x 4GB TF card (IO firmware preloaded).
- 3 x Connecting Cables.
- 1 x Pixhawk PPM Encoder Module.
- 1 x JR plug 10P input end of the cable (100mm).
- 1 x JR plug 4P output end of the cable (100mm).
- 1 x Glass Fiber Flight Controller Anti-vibration/Shock Absorber Set.
- 1 x NEO-M8N GPS Module with translucent Shell.
- 2 x cables (APM/PIX).
- 1 x GPS Folding Base Antenna Set.
- 1 x APM 2.5.2/2.6/2.8 Pixhawk Power Module.
- 1 x I2C Splitter with Cable.
- 1 x OSD OLED Display.
Reviews
There are no reviews yet.